AnySense - Telemetry Modul for Naza, Phantom and Wookong

AnySense – Telemetry Module

49,9559,95

Clear

AnySense turns your Radio Control into a real-time telemetry system with no costs for additional hardware, such as a GPS sensor, voltage module or vario.
Additionally all data will also be saved on the storage card of your remote control. With the right tools, you can easily visualise the content of the storage card, export it to Excel or even embed it into existing videos.

Weight 0.03 g
Kompatible Autopilot-Systeme

DJI Wookong M, DJI Naza-M, DJI Naza-M V2, DJI Phantom 2, DJI Phantom 1

Kompatible R/C Systeme

Futaba S.Bus2, Spektrum X-Bus, GRAUPNER/SJ HoTT, Multiplex MSB, Jeti Duplex EX, FrSky S.Port, Mavlink

Gewicht

5g

Lieferumfang

1x AnySense Telemetrie Modul, 1x AnySense Telemetrie Kabel

Abmessungen

ca.: 22 x 42 x 10 mm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

SKU: 10001 - Need Help? Contact Us Leave Feedback

Tags: , , , , , , , , , , , , , , , ,

Share

Plug & Fly

Easy to install and setup in just 3 Steps:

  1. Connect the AnySense to the CAN Bus
  2. Select your Telemetry System
  3. Connect it to your RC-Receiver

Now you are ready to Fly.

Connectivity

Further information can be found in the AnySense – Instruction Manual.

Telemetry Information

  • GPS Position (Latitude/Longitude)
  • RTH/Failsafe Home Position (Latitude/Longitude)
  • GPS satellites
  • GPS Fix (0=No, 2=2D, 3=3D, 4=DGPS)
  • GPS Speed (in km/h)
  • GPS Altitude (in m)
  • GPS Variometer (in m/s)
  • GPS Flightdirection (in degree)
  • Flightmode (0=Manuell, 1=GPS, 2=Failsafe, 3=Atti.)
  • Barometric Altitude (in m) (very accurate)
  • Barometric Variometer (in m/s)
  • Nick and roll (in degree)
  • Compass (in degree)
  • Battery (in volt)
  • Current (in ampere) *
  • Capacity (in mAh) *
  • Lipo Sensor (in volt) *
* only Phantom 2 or additional FrSky sensors

MAVLink support (e.g. MinimOSD, Amimon Connex)

With the support of the MAVLink protocol, the AnySense adapts the disparity between the standard protocol that is widespread in the multicopter segment and the DJI products.

Thus DJI pilots also gain access to many add-ons and expert functions that were previously only available for other flight controllers.

The MinimOSD is a very flexible OSD, which makes it possible to set up two different views for the OSD, so-called panels, and to change from one panel to another during operation using a switch on the remote control.

An optionally available AnySense MAVLink OSD cable is available for connecting to the AnySense to simplify the connection to the OSD.

FrSky Sensor addons

As a further useful function, the AnySense allows the value-for-money sensors from the manufacturer FrSky to be connected to the telemetry systems from Graupner/SJ, Futaba, Jeti and MAVLink.

Thereby, the sensor data of the following FrSky sensors are prepared for the Futaba S.Bus2, Jeti Duplex EX, Graupner/SJ HoTT or MAVLink and correspondingly transmitted to your remote control.

  • LiPo sensors (FrSky FLVSS)
  • Current sensor 40 A (FrSky FCS-40)
  • Current sensor 150 A (FrSky FCS-150)

Up to 12 cells and more can be measured by using several LiPo sensors. At the same time several current sensors can also be connected in order to be able to measure currents above 150A.

For connecting the FrSky sensors, an optionally available AnySense – Telemetry cable is required.

Spektrum X-Bus

The AnySense – Spektrum Telemetry Cable is required in order to connect your AnySense to the Spektrum Telemetry Module. This gives you the Plug & Play performance with the Spektrum Telemetry System.

Futaba S.Bus2 (FASSTest, T-FHSS)

The AnySense is compatible with any S.BUS2 receiver and act as following Futaba Sensors:

  • VARIO-1672
  • CURR-1678
  • SBS-01G
  • Lowest cell voltage in mV (SBS-01RM/0)
  • Compass in degree (SBS-01RM/0)
  • Number of Satellites (SBS-01T)
  • Naza Flight-Mode (SBS-01T) (0=Manual, 1=GPS, 2=Failsafe, 3=Atti.)
  • Lipo Temperature (SBS-01T)

Multiplex MSB

The Multiplex MSB Telemetry up to 16 Telemetry values from Addresse 0 to Addresse 15. The has to be distinct over any connected Sensor connected to Sensor Bus. In the Konfiguration Manager Tool, you can select which Address (0-15) delivers which telemetry value of the AnySense. You can also disable the telemetry output for Address, if the Address is used by another Sensor on the Bus.

 

Graupner/SJ HoTT

The AnySense replaces the GPS, EAM, GAM and Vario Sensor. How the informations are displayed, depends on your Graupner remote.

Multicopter Telmetry Screen

Graupner/SJ MZ-24 - GPS Telemetry Screen

Graupner/SJ MX-12/16/20

Multicopter Telmetry Screen

GPS Telemetry Screen

GPS Telemetry Screen 2

Vario Telemetry Screen

GAM Telemetry Screen

Jeti Duplex EX

The Jeti Duplex EX system allows up to 15 telemetry values to be transmitted. As the AnySense can supply more values, in the standard configuration the telemetry values depicted will be transmitted.

Sensor selection

Telemetry Screen 1

Telemetry Screen 2

Sensor selection

Telemetry Screen 3

Telemetry Screen 4

FrSky S.Port (Taranis)

Spd
Speed in km/h based on the GPS position change.
Hdg
Flightdirection in degree. Selectable: Course over Ground, (Tilt compensated-) compass
GAlt
GPS based altitude in meter.
Alt
Barometric altitude in meter.
VSpd
Vertical speed in m/s. Selectable: barometric or GPS
Dist
Distance to home
AccX, AccY
X,Y angle in degree
VFas
Battery voltage in volt.
Cel
Lowest Lipo voltage in volt*
Curr
Current in Ampere*
Cnsp
Total current consumption in milliampere/Hour*
T1
Number of GPS satellites.
T2
GPS Fix: 0 = No Fix, 2= 2D, 3 = 3D, 4 = DGPS
* only with Phantom 2 or additional FrSky sensors